Chapter 97 SNAX‑CRE Messages

The messages in this chapter are sent by the SNAX Creator‑2 subsystem. The subsystem ID displayed by these messages includes SNAX‑CRE as the subsystem name.




	NOTE: Negative-numbered messages are common to most subsystems. If you receive a negative-numbered message that is not described in this chapter, see Chapter 15.

crename: Connection to subdev lost due to file system error ferr from procedure procname, file filename filerole: explanation

`crename`	is the name of the SNAX Creator‑2 subsystem that reported the error.
`subdev`	is the name of the subdevice associated with the connection failure.
`ferr`	is the file‑system error code. See Appendix B, for a brief description of the error code.
`procname`	identifies a procedure referred to in the error.
`filename`	is the name of the file associated with the file‑system error.
`filerole`	identifies the role played by the file associated with the file‑system error.
`explanation`	explains the file‑system error that led to the lost connection.

Cause A connection to a subdevice was lost due to a file‑system error.

Effect The connection is marked as being in the error state; it is retried periodically. No further event is produced until the connection succeeds or the subdevice is deleted.

Recovery Verify that the access method manager process is operational.

crename: Connection to subdev cannot be established due to file system error ferr from procedure procname, file filename filerole: explanation

`crename`	is the name of the SNAX Creator‑2 subsystem that reported the error.
`subdev`	is the name of the subdevice associated with the failed connection.
`ferr`	is the file‑system error code. See Appendix B, for a brief description of the error code.
`procname`	identifies a procedure referred to in the error.
`filename`	is the name of the file associated with the file‑system error.
`filerole`	identifies the role played by the file associated with the file‑system error.
`explanation`	explains the file‑system error that prevented the connection from being established.

Cause A connection to a subdevice could not be established.

Effect The connection is marked as being in the error state and is retried periodically. No further event occurs until the connection succeeds or the subdevice is deleted.

Recovery The following are possible actions you can take to correct this problem:

Check that the name of the subdevice matches the name of the APPL object defined (to the access method manager process) for SNAX Creator‑2.
Check that the access method manager process is operational.
Check that the password (defined to SNAX Creator‑2) for the subdevice matches the password (defined to the access method) for the SNAX Creator‑2 APPL object.

crename: Connection to subdev restored

`crename`	is the name of the SNAX Creator‑2 subsystem that sent the message.
`subdev`	is the name of the subdevice associated with the connection.

Cause A connection to a subdevice was restored.

Effect None

Recovery Informational message only; no corrective action is needed.

crename: Connection to subdev established

`crename`	is the name of the SNAX Creator‑2 subsystem that sent the message.
`subdev`	is the name of the subdevice associated with the connection.

Cause A connection to a subdevice was established.

Effect None

Recovery Informational message only; no corrective action is needed.

crename: Connection to subdev deleted

`crename`	is the name of the SNAX Creator‑2 subsystem that sent the message.
`subdev`	is the name of the subdevice associated with the connection.

Cause A connection to a subdevice was terminated by operator request.

Effect The subdevice connection is terminated.

Recovery Informational message only; no corrective action is needed.

crename: Connection to subdev abandoned during evaluation of the badattr attribute: explanation

`crename`	is the name of the SNAX Creator‑2 subsystem that reported the error.
`subdev`	is the name of the subdevice associated with the failed connection.
`badattr`	is the attribute whose evaluation was in error.
`explanation`	explains the reason that the attribute could not be evaluated.

Cause A connection to a subdevice could not be initiated because of an error in the configuration definition of the subdevice.

Effect No further attempt is made to establish this connection until the operator changes the definition of the subdevice.

Recovery Use the INFO command to examine the attributes of the subdevice and make any necessary corrections.

crename: Activation of application applname [ (program program) ] on behalf of requester reqname on openname failed because explanation

`crename`	is the name of the SNAX Creator-2 subsystem that reported the error.
`applname`	is the name of the application that failed to be activated.
`program`	is the name of the Pathway subsystem PROGRAM object that was invoked when the Pathway application was launched.
`reqname`	is the name of the requester. For SNAX/XF and SNAX/APN, this is the file name of the requesting LU.
`openname`	is the name of the terminal that opened the session.
`explanation`	explains the reason that an application failed to be started.

Cause An attempt to start an application failed.

Effect The request is rejected. A diagnostic message is displayed on the requesting terminal screen.

Recovery Recovery depends on the explanation for the failure.

crename:Run started at starttime, ended at endtime on openname requester:reqname service:svcname appl:applname { PATHWAY:pathmon:pathmon program:program termname:pwyterm } { TACL:process:taclname } { SERVER:server:servname }

`crename`	is the name of the SNAX Creator-2 subsystem that reported the error.
`starttime`	is the time at which the session was initiated.
`endtime`	is the time at which the session was terminated.
`openname`	is the name of the terminal that opened the session.
`reqname`	is the name of the requester. For SNAX/XF and SNAX/APN, this is the file name of the requesting LU.
`svcname`	is the name of the requested service. For SNAX/XF and SNAX/APN, this is the name of the LU that was accessed.
`applname`	is the name of the application that was running prior to the termination of the session.
`pathmon`	is the name of the PATHMON process.
`program`	is the name of the Pathway subsystem PROGRAM object that was invoked when the Pathway application was launched.
`pwyterm`	is the name of the TERM object assigned by the Pathway subsystem to the thread that was initiated.
`taclname`	is the name of the TACL process.
`servname`	is the name of the server process that was associated with the activation of a server application.

Cause A session initiated by the SNAX Creator-2 subsystem has been terminated. This message contains the accounting information.

Effect None

Recovery Informational message only; no corrective action is needed.

crename:Run started at starttime requester:reqname service:svcname appl:applname { PATHWAY:pathmon:pathmon program:program termname:pwyterm } { TACL:process:taclname } { SERVER:server:servname }

`crename`	is the name of the SNAX Creator‑2 subsystem that sent the message.
`starttime`	is the time at which the session was initiated.
`reqname`	is the name of the requester. For SNAX/XF and SNAX/APN, this is the file name of the requesting LU.
`svcname`	is the name of the requested service. For SNAX/XF and SNAX/APN, this is the name of the LU that was accessed.
`applname`	is the name of the application that was running prior to the termination of the session.
`pathmon`	is the name of the PATHMON process.
`program`	is the name of the Pathway subsystem PROGRAM object.
`pwyterm`	is the name of the TERM object assigned by the Pathway subsystem to the thread that was initiated.
`taclname`	is the name of the TACL process.
`servname`	is the name of the server process that was associated with the activation of a server application.

Cause A session has been initiated.

Effect None

Recovery Informational message only; no corrective action is needed.