Operator Messages Manual
Chapter 7 BRU (Backup and Restore 2.0) Messages
The messages in this chapter are generated by the Backup and
Restore 2.0 subsystem. The subsystem ID displayed by these messages
includes BRU as the subsystem name. When the message is displayed
on your terminal, it is preceded by either Error, Info, or Warning. | | | | | NOTE: Negative-numbered messages are common to most subsystems. If
you receive a negative-numbered message that is not described
in this chapter, see Chapter 15. | | | | |
5000 Error 5000 Job ID: job-id Process Name: process-name Component: component The
DMA, process-name, failed
to start the job. Return code: rc File: file-name Line:
line-num | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the data management application
(DMA) process. | component | is the data management application (DMA) component
of Backup and Restore 2.0. | rc | is the return code. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A serious configuration problem occurred. Either a transient
resource shortage occurred or a more permanent problem
exists. Effect The job terminates. After the DMA process issues this
message, the DMA terminates because an aspect of job
initialization failed. This message might also be accompanied
by one or more 5002 messages, typically when the DMA attempts
to start a Tape Service or Data Service and an aspect
of the services’ initialization fails. Recovery Perform these steps: Determine the reason for failure. For example, sufficient
virtual memory might not be available in a given processor
for segment allocation in a starting process, or parsing
the BRCMD file was not successful. Make any necessary changes. Correct the configuration
problem. Try the BACKUP or RESTORE command again. If the Backup or Restore job fails again, gather all
relevant EMS logs and SaveAbend files and contact your
service provider.
|
5001 Info 5001 - Job ID: job-id Process Name: process-name Component: component The job has been started. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA) component
of Backup and Restore 2.0. |
Cause The data management application (DMA) successfully started
the job. Effect None. Recovery None required. This message is informational only. |
5002 Error 5002 - Job ID: job-id Process Name: process-name Component: component The
job was aborted. File: file-name Line: line-num | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A job aborted without completing all assigned work and is
nonresumable. You might have specified a tape device name
that does not exist. Effect The job terminates. Recovery Check the Event Management Service (EMS) logs. This message
is usually accompanied by other event messages. Perform
these steps: Determine the reason for failure. Make any necessary changes. Try the BACKUP or RESTORE command again. If the Backup or Restore job fails again, gather all
relevant EMS logs and SaveAbend files and contact your
service provider.
|
5003 Info 5003 - Job ID: job-id Process Name: process-name Component: component The
job completed. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. |
Cause A job concluded after completing all assigned work. Effect None. Recovery None required. This message is informational only. |
5004 Error 5004 - Job ID: job-id Process Name: process-name Component: component The
component is aborting due to internal failure or resource
shortage. File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The DMA, Tape Service, or Data Service is aborting because
of either a transient resource shortages or a permanent
internal failure. Effect The job terminates. Recovery Perform these steps: Check the Event Management Service (EMS) logs. This
message is usually accompanied by other event messages
inserted in the EMS log. Determine the reason for failure. This event indicates
a serious problem. Make any necessary changes. Try the BACKUP or RESTORE command again. If the Backup or Restore job fails again, gather all
relevant EMS logs and SaveAbend files and contact your
service provider.
|
5005 Error 5005 - Job ID: job-id Process Name: process-name Component: component Parser
error encountered while parsing the file cs-file-name. Error: parser-error File: file-name. Line:
line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA) component
of Backup and Restore 2.0. | cs-file-name | is the name of the Backup and Restore command stream
(BRCMD) file. | parser-error | is the error received while the DMA is parsing the
BRCMD file. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The data management application (DMA) received an error
while parsing the Backup and Restore command stream (BRCMD)
file. Typically, either a shortage of resources exists,
or the BRCMD file has been corrupted or modified. Effect The job terminates. Recovery Issue the command again from BRCOM. If the error persists,
gather all relevant Event Management Service (EMS) logs
and SaveAbend files and contact your service provider. |
5006 Error 5006 - Job ID: job-id Process Name: process-name Component: component The
component received File System error fserr on
error-file-name. File file-name.
Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | fserr | is the file-system error. | error-file-name | is the name of the Backup and Restore 2.0 file where
the error occurred. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A file-system error was returned in response to a
file-system procedure call (for example, open, read,
write). Effect The job terminates. Recovery Fix the problem and try the BACKUP or RESTORE command again.
. |
5007 Error 5007 - Job ID: job-id Process Name: process-name Component:component {The
component was unable to allocate memsize bytes | The
component was unable to allocate memory. File: file-name
Line: line-num | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | memsize | is the amount of memory. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The component was unable to allocate the requested block of
memory. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5008 Warning 5008 - Job ID: job-id Process Name: process-name Component: component The
component received a message from the sender-component
that is invalid for the current state. State: state.
Msg: ndmp-msg. File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | sender-component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0
that sent the message. | state | is the state of the Backup or Restore job. | ndmp-msg | is the Network Data Management Protocol message. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A component sent another component an invalid message for
the latter's current state. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5009 Error 5009 - Job ID: job-id Process Name: process-name Component: component The
component was unable to create an extended data segment.
Size: memsize. Error: error Error detail: error-detail-int | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | memsize | is the amount of memory. | error | is the error. | error-detail-int | is the error detail. |
Cause The component was unable to create an extended data
segment. Effect The job terminates. Recovery Correct the problem and try the BACKUP or RESTORE command
again. |
5010 Error 5010 - Job ID: job-id Process Name: process-name Component: component The
message sent by the sender-component to the component
has an illegal argument value. Msg: ndmp-msg. Argument
name: argument-name. Argument value: argument-value.
File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | sender-component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0
that sent the message. | ndmp-msg | is the Network Data Management Protocol message. | argument-name | is the name of the argument. | argument-value | is the value of the argument. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A message that was sent had an illegal argument
value. Effect The job terminates Recovery Determine the reason for failure, make any necessary
changes, and attempt to try the BACKUP or RESTORE command again.
If the Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5011 Error 5011 - Job ID: job-id Process Name: process-name Component: component An
XDR error was returned attempting to xdr-op a message.
File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | xdr-op | is the external data representation ( XDR) operation,
either encode or decode. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause An error was encountered while encoding or decoding an NDMP
message. Effect The job terminates. Recovery Try the BACKUP or RESTORE command again. If the Backup or
Restore job fails again, gather all relevant Event Management
Service (EMS) logs and SaveAbend files and contact your
service provider. |
5012 Error 5012 - Job ID: job-id Process Name: process-name Component: component The
fspersonality smart agent returned an error in response
to a agent-op operation. Error: errordetail. File: file-name.
Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | fspersonality | is OSS or SQL/MX. | agent-op | is the operation. | errordetail | is the detail of the error. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The fspersonality smart agent returned errordetail to the
component. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5013 Error 5013 - Job ID: job-id Process Name: process-name Component: component The
component received a reply with an error indicated from
the sender-component. Msg: ndmp-msg. Error: ndmp-error.
File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | sender-component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0
that sent the message. | ndmp-msg | is the Network Data Management Protocol message. | ndmp-error | is the Network Data Management Protocol error. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A component replied with an error indicator in response to a
message sent by another component. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5014 Error 5014 - Job ID: job-id Process Name: process-name Component: component The
component received File system error fserr (err-text)from
the message library. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | fserror | is the file-system error. | err-text | is the text of the error. |
Cause A file-system error was returned in response to a message
library procedure call. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5015 Error 5015 - Job ID: job-id Process Name: process-name Component: component An
error was returned attempting to list information to
the output file. Error: error-detail. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | error-detail | is the error detail. |
Cause Listing information to the output file failed. Effect The task terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5016 Error 5016 - Job ID: job-id Process Name: process-name Component: component The
component was unable to start the ndmp-component. Error:
error. Error Detail: error-detail. File: file-name.
Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA) component
of Backup and Restore 2.0. | ndmp-component | is the Data Service or Tape Service component of Backup
and Restore 2.0. | error | is the error. | error-detail | is the error detail. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The DMA could not start the Data Service or the Tape
Service. Effect The job terminates. Recovery This event indicates a serious problem. It is usually
accompanied by other event messages in the Event Management
Service (EMS) log. Determine the reason for failure, make
any necessary changes, try the BACKUP or RESTORE command
again. If the Backup or Restore job fails again, gather
all relevant EMS logs and SaveAbend files and contact
your service provider. |
5017 Error 5017 - Job ID: job-id Process Name: process-name Component: component The
sender-component sent an unexpected notification message,
ndmp-msg. File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA) component
of Backup and Restore 2.0. | sender-component | is the Data Service or Tape Service component of Backup
and Restore 2.0. | ndmp-msg | is the Network Data Management Protocol message. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause Either the Data Service or the Tape Service sent an
unexpected notification message to the DMA. Effect The job terminates. Recovery This event indicates a serious problem. It is usually
accompanied by other event messages in the Event Management
Service (EMS) log. Determine the reason for failure, make
any necessary changes, and try the BACKUP or RESTORE command
again. If the Backup or Restore job fails again, gather
all relevant Event Management Service (EMS) logs and SaveAbend
files and contact your service provider. |
5018 Error 5018 - Job ID: job-id Process Name: process-name Component: component The
tape file, tape-file on
tape-volume, failed verification.
| job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | tape-file | is the tape file. | tape-volume | if the tape volume. |
Cause Tape verification failed. There might be a problem with the
tape cartridge, or the tape drive might need to be cleaned. Effect The tape might be unusable. Recovery Try a different tape cartridge. If the problem continues,
clean the tape drive and then try the BACKUP or RESTORE
command again. |
5019 Warning 5019 - Job ID: job-id Process Name: process-name Component: component The
fs-personality object,
object-name, could not be backed
up. Error: error-detail.
File: file-name. Line:
line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | fs-personality | is OSS or SQL/MX. | object-name | is the name of the object. | error-detail | is the error detail. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause An object could not be backed up. Effect None. Recovery This message is informational only. |
5020 Warning 5020 - Job ID: job-id Process Name: process-name Component: component The
fs-personality object,
object-name, could not be restored.
Error: error-detail. File:
file-name. Line:
line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | fs-personality | is OSS or SQL/MX. | object-name | is the name of the object. | error-detail | is the error detail. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause An object could not be restored. Effect None. Recovery This message is informational only. |
5021 Error 5021 - Job ID: job-id Process Name: process-name Component: component Error
processing define define-name: error-text. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is a DEFINE name of CLASS TAPE or CLASS TAPECATALOG.
This DEFINE sends a request to the labeled-tape server
process ($ZSVR) for labeled-tape processing. | error-text | is the text of the error. |
Cause The DEFINE specifies a label type other than Backup or
Omitted. Effect The job terminates. Recovery Change the DEFINE label specification to Backup or Omitted
and try the BACKUP or RESTORE command again. |
5022 Error 5022 - Job ID: job-id Process Name: process-name Component: component An
operation command was issued,
but there are no objects to satisfy the criteria specified,
so no change will be made. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | operation | is BACKUP or RESTORE. |
Cause No objects match the criteria specified in the BACKUP or
RESTORE command. Effect The changes are not made to the tape or disk media. The
object you specified is not backed up or restored. Recovery None. This is an informational message only. |
5023 Warning 5023 - Job ID: job-id Process Name: process-name Component: component Enscribe
and SQL/MP objects will not be backed up. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. |
Cause You used Backup and Restore 2.0 to backup OSS or SQL/MX
objects. Effect Enscribe and SQL/MP objects are not backed up. Recovery None. This is an informational message only. |
5024 Error 5024 - Job ID: job-id Process Name: process-name Component: component An
unexpected close was received from the DMA. Terminating. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA) component
of Backup and Restore 2.0. |
Cause An unexpected close was received from the data management
application (DMA). Effect The job terminates. Recovery Determine what caused the DMA to stop. Correct the problem
and try the BACKUP or RESTORE command again. |
5025 Error 5025 - Job ID: job-id Process Name: process-name Component: component Error
error was returned in response
to a DSM/TC operation. File: file-name Line: line-num.
| job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | error | is the error. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The component tried a DSM/TC operation that failed. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5026 Error 5026 - Job ID: job-id Process Name: process-name Component: component The
DMA's attempt to connect to the service-component timed-out. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA) component
of Backup and Restore 2.0. | service-component | is the Data Service or Tape Service component of Backup
and Restore 2.0. |
Cause The data management application (DMA) did not receive an
open from the Data Service or Tape Service component before
timing out. Effect The job terminates. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5027 Error 5027 - Job ID: job-id Process Name: process-name Component: component The
component encountered an
internal error. State: state. File: file-name. Line:
line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | state | is the state of the job. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The component encountered an internal software error. Effect The job terminates. Recovery Try the BACKUP or RESTORE command again. If the Backup or
Restore job fails again, gather all relevant Event Management
Service (EMS) logs and SaveAbend files and contact your
service provider. |
5028 Info 5028 - Job ID: job-id Process Name: process-name Component: component The
component received an unexpected system message, sysmsg,
from process-name. Cpu: cpu. Pin: pin | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | sysmsg | is a system message. | process-name | is the process name for the component that received
an unexpected system message. | cpu | is the processor. | pin | is the process identification number. |
Cause The component received an unexpected system message. Effect None. Recovery None. |
5029 Error 5029 - Job ID: job-id Process Name: process-name Component: component device
is not ready. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | device | is the name of the magnetic tape unit, such as
$TAPE1. |
Cause A tape drive is unavailable or offline, or a tape is not
mounted in the tape drive. Backup and Restore 2.0 polls until
it finds that the problem has been corrected. Effect The job cannot proceed until the problem is fixed. Recovery Make the tape drive available, put it online, or mount a
tape, whichever is appropriate to fix the problem. |
5030 Error 5030 - Job ID: job-id Process Name: process-name Component: component The
tape volume on device is write protected. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | device | is the name of the magnetic tape unit, such as
$TAPE1. |
Cause The mounted tape volume is correct, but write is not
enabled. Effect The system unloads the tape, and the requesting application
is suspended until the write-protect problem is corrected
and the tape is mounted again. Recovery Enable writing to the tape and remount the tape. |
5031 Error 5031 - Job ID: job-id Process Name: process-name Component: component The
free-buffer list is inconsistent with the in-use-buffer
list. File: file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the Data Service or Tape Service component of Backup
and Restore 2.0. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause An error occurred while the Data Service or Tape Service was
processing the shared memory buffer. Effect The job is stopped. Recovery Determine the reason for failure, make any necessary
changes, and try the BACKUP or RESTORE command again. If the
Backup or Restore job fails again, gather all relevant
Event Management Service (EMS) logs and SaveAbend files
and contact your service provider. |
5033 Error 5033 - Process Name: process-name Component: component Deleting invalid file file-name. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | file-name | is the name of the BRJOBS file or BRCONFIG file. |
Cause Either the BRJOBS file or BRCONFIG file is invalid. Effect The invalid file is deleted if possible. If the file is
deleted, either a new empty BRJOBS file or a new BRCONFIG
file with default configuration values is created. Recovery If the BRJOBS file or BRCONFIG file is deleted and
re-created, either use the new file or restore a previous version
of the file. If the BRJOBS file or BRCONFIG file is not
deleted, either use the DELETE command to delete the file
and allow a new file to be created or restore a previous
version of the file. |
5034 Error 5034 - Process Name: process-name Component: component No more automatically-generated
jobids available. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. |
Cause No more automatically generated job IDs are available.
Automatically generated job IDs consist of the letters ZBR
and a 5-digit hexadecimal number from ZBR00000 through
ZBRFFFFF. A job ID is in use if that job ID exists in
the BRJOBS file or if any files exist in the $brjobsvolume.jobid subvolume. Effect The job fails. Recovery To manually specify the job ID for backup and restore jobs
until automatically generated job IDs are made available,
retry the BACKUP or RESTORE command and specify a job
ID using the JOB job option. To make more automatically generated job IDs available: Use the CLEANUP JOB command to purge temporary files from
old BACKUP and RESTORE jobs. Use the DELETE JOB command to remove old jobs from the
BRJOBS file. Manually purge trace files and any other files for old
jobs.
|
5035 Error 5035 - Job ID: job-id Process Name: process-name Component: component This
tape can only be restored with Backup/Restore 2.0. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. |
Cause Backup and Restore 2.0 was used to back up the objects. Effect None. Recovery None. This is an informational message only. |
5036 Error 5036 - Job ID: job-id Process Name: process-name Component: component The
CLASS attribute value for DEFINE define-name, is neither
TAPE nor TAPECATALOG. File: file-name Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The CLASS attribute value for the DEFINE is neither TAPE nor
TAPECATALOG. Effect The job terminates. Recovery Alter the CLASS attribute value to TAPE or TAPECATALOG. Try
the BACKUP or RESTORE command again. |
5037 Error 5037 - Job ID: job-id Process Name: process-name Component: component The
LABELS attribute value for DEFINE define-name, is neither
BACKUP nor OMITTED. File: file-name Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The LABELS attribute value for the DEFINE is neither BACKUP
nor OMITTED. Effect The job terminates. Recovery Alter the DEFINE LABELS attribute value to BACKUP or
OMITTED. Try the BACKUP or RESTORE command again. |
5038 Error 5038 - Job ID: job-id Process Name: process-name Component: component The
AVRSYSTEM or SYSTEM attribute value for DEFINE define-name,
is not available. File: file-name Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The AVRSYSTEM (CLASS TAPECATALOG) or SYSTEM (CLASS TAPE)
attribute specified in the DEFINE is not available. Effect The job terminates. Recovery Establish communication with the system. Try the BACKUP or
RESTORE command again. |
5039 Error 5039 - Job ID: job-id Process Name: process-name Component: component LABELS
BACKUP was specified for DEFINE define-name, but the
system is not configured for labeled tape support. File:
file-name Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause LABELS BACKUP was specified for the DEFINE define-name, but
the system is not configured for labeled tape support. Effect The job terminates. Recovery Configure the system for labeled tape support . Try the
BACKUP or RESTORE command again. |
5040 Error 5040 - Job ID: job-id Process Name: process-name Component: component DEFINE
define-name, that specifies an AVRSYSTEM or SYSTEM,
system that has an OS version
that doesn’t support Backup/Restore 2.0. File:
file-name Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. | system | is a system. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause The AVRSYSTEM (CLASS TAPECATALOG) or SYSTEM (CLASS TAPE)
attribute specified in the DEFINE is running software that
does not support Backup and Restore 2.0. Effect The job terminates. Recovery Install the required release version update (RVU) and any
needed software product revisions (SPRs) for Backup and
Restore 2.0. |
5041 Error 5041 - Job ID: job-id Process Name: process-name Component: component DEFINE
define-name, specified DENSITY which is not suppported
for cartridge tape media. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. |
Cause You specified a DEFINE attribute DENSITY, but DENSITY is not
supported for cartridge tapes. Effect None. The attribute is ignored. Recovery None. This message is informational only. |
5042 Error 5042 - Job ID: job-id Process Name: process-name Component: component DEFINE
define-name, specified the TAPEMODE attribute which
is not suppported on G-series OS versions. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | define-name | is the name of the DEFINE. |
Cause You specified the DEFINE attribute TAPEMODE, but TAPEMODE is
not supported on G-series release version updates (RVUs). Effect None. The attribute is ignored. Recovery None. This message is informational only. |
5043 Error 5043 - Job ID: job-id Process Name: process-name Component: component Internal
error- the component encountered the following message
library error (error ) error-detail. File file-name.
Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | error | is the error. | error-detail | is the error detail. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A message library error was returned in response to a
library procedure call. Effect The job terminates. Recovery This is an internal error. Gather all relevant Event
Management Service (EMS) logs and SaveAbend files and contact
your service provider. |
5044 Error 5044 - Job ID: job-id Process Name: process-name Component: component Internal
error- the component received an NDMP message with an
invalid sequence number , seq-num, from sender-component.
Msg: ndmp-msg. File file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | seq-num | is the sequence number of the Network Data Management
Protocol message. | sender-component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0
that sent the message. | ndmp-msg | is the Network Data Management Protocol message. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause An NDMP message with an incorrect sequence number was
received . Effect The job terminates. Recovery This is an internal error. Gather all relevant Event
Management Service (EMS) logs and SaveAbend files and contact
your service provider. |
5045 Error 5045 - Job ID: job-id Process Name: process-name Component: component A
disk media error occurred during Backup. The job option,
IGNORE, is on so the data record has been null padded
and written to tape. Data file: data-file-name. File
file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | data-file-name | is the name of the data file. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A disk media error occurred during a backup job. Effect The data record is null padded and written to disk. Recovery None. This is an informational message only. |
5046 Error 5046 - Job ID: job-id Process Name: process-name Component: component A
tape media error was encountered during Restore. The
job option, IGNORE, is on so the data record has been
null padded and written to tape. Data file: data-file-name.
File file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | data-file-name | is the name of the data file. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause A tape media error occurred during a restore job. Effect The data record is null padded and written to disk. Recovery None. This is an informational message only. |
5047 Error 5047 - Job ID: job-id Process Name: process-name Component: component Internal
error- an error was returned in response to an intermediate
catalog operation. Operation: agent-op. Error: error-detail.
File file-name. Line: line-num. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | agent-op | is the operation. | error-detail | is the detail of the error. | file-name | is the name of the Backup and Restore 2.0 source
file. | line-num | is the line number within the source file where the
error occurred. |
Cause An intermediate catalog operation failed. Effect The task terminates. Recovery This is an internal error. Gather all relevant Event
Management Service (EMS) logs and SaveAbend files and contact
your service provider. |
5051 Error 5051 - Job ID: job-id Process Name: process-name Component: component An
invalid job operation job-op was received. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | job-op | is the type of job. |
Cause The job operation was neither a backup nor restore. Effect The job terminates. Recovery Gather all relevant Event Management Service (EMS) logs and
SaveAbend files and contact your service provider. |
5052 Error 5052 - Job ID: job-id Process Name: process-name Component: component An
unexpected close was received from the Data Service.
Terminating. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the Data Service component of Backup and Restore
2.0. |
Cause The Data Service stopped unexpectedly. Effect The job terminates. Recovery Determine what caused the Data Service to stop. Correct the
problem and and try the BACKUP or RESTORE command again. |
5053 Error 5053 - Job ID: job-id Process Name: process-name Component: component Please
mount a tape with labels BACKUP on device. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | device | is the name of the magnetic tape unit, such as
$TAPE1. |
Cause You have not mounted a labeled tape for the BACKUP
job. Effect The job waits for a labeled tape to be mounted. Recovery Mount a labeled tape on device. |
5054 Error 5054 - Job ID: job-id Process Name: process-name Component: component Please
mount an unlabeled tape on device. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | job-op | is the type of job. |
Cause You have not mounted a unlabeled tape for the BACKUP
job. Effect The job waits for an unlabeled tape to be mounted. Recovery Mount a labeled tape on device. |
5055 Warning 5055 - The backup job cannot be
restored because the ABORT command or STOP command was issued.
| Cause An operator issued an ABORT or STOP command during a backup
operation. Effect The job continues to perform the abort or stop operation. Recovery None. This is an informational message only. |
5056 Error 5056 - The component encountered an illegal option
specification: error-detail.
File: file, line: line. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. | error-detail | is the error detail | file | is the name of the Backup and Restore 2.0 source
file. | line | is the line number within the source file where the
error occurred. |
Cause The component encountered an illegal option specification
from the user for this operation. Effect The job terminates. Recovery Correct the option specification and retry. |
5062 Warning 5062 - Job ID: job-id Process Name: process-name Component: component To
avoid any data inconsistency issue, use TPART, INDEX,
and IPART in the BACKUP OR RESTORE command with care. | job-id | is a valid, unique job identifier with a maximum of
eight characters. job-id is not case-sensitive. | process-name | is the process name for the component of Backup and
Restore 2.0. | component | is the data management application (DMA), Data Service,
or Tape Service component of Backup and Restore 2.0. |
Cause TPART, INDEX, or IPART keyword was used in the BACKUP or
RESTORE command. Effect None. Recovery None. This message is informational only. |
|